HOME Knowledge

Contact

Knowledge

  • Use the key steps timken bearings

    1 , shaft and bearing tolerances selection and control of the bearing pressed into the bearing block should be flexible rotation without sense . If significant rotation is not flexible , it indicates the size of the shaft is too great, the tolerance to be reduced. If bearings pressed into the shaft turned by hand after a significant "imperfections " sense , it may be too much tolerance of the shaft or shaft roundness bad . So when good control sh [...]

  • Three ways to prevent early timken bearing failure

    1 , strengthen quality inspection and supervision of bearing products to ensure product quality spherical bearings meet the relevant standards or design requirements.2 , the use of advanced technology to improve the life and reliability of the bearing. Including structural optimization , process reform , material selection and concise , efficient noble of lubrication, assembly and installation , and so fine .3 , to strengthen the United States im [...]

  • Timken bearing installation should pay attention to four issues

    In order to improve the efficiency and service life of the bearing timken during use , the installation timken bearings must pay attention to the following four items:1, Timken bearings should be installed in the clean , clean room , timken bearings should carefully matching , timken bearing spacer to go through the grind , keep the inner and outer rings under the premise of high spacer , spacer parallelism 1um should be controlled in the followi [...]

  • About timken bearing hydrodynamic FAQ What?

    Hydrostatic timken bearings means is the use of a special oil, the oil pressure with a certain static pressure oil chamber into the bearing. Forming a film pressure, pressure difference between the static pressure chamber, a balance load, the bearing lubrication in a fully liquid state of work.1, the depth of the cavity structure mixed timken bearings: high-speed cylindrical grinding machine spindle M1432, MGA6025 grinding tools, such as light lo [...]

  • timken bearing steel special purpose ultra-clean development

    In recent years, with high-speed and miniaturization have become increasingly demanding, therefore, timken bearings high performance requirements. Especially in the automotive industry to reduce fuel consumption and reduce vehicle of this size has a high demand. On the other hand, the electronics industry also requires very little relationship to promote energy conservation and more time when there is no electronic equipment vibration. A, with u [...]

  • timken bearing the new seal structure extend its life

    timken bearings if in harsh environments, bearing seals and sealing cover is essential, because they prevent dirt intrusion, extending bearing life. Mill rolls usually consists of four sealed tapered roller bearings. When using a strong impact load required to withstand water and debris intrusion.timken company developed the super-easy to clean sealed roll neck bearings. This bearing lubrication in harsh conditions, the load capacity increased by [...]

  • TIMKEN bearing radial clearance exciting implications for operation

    Because manipulation or installation errors, TIMKEN bearing raceways and move the body may be damaged. In operation, the rolled damaged bearing member will produce a particular frequency. Frequency analysis can identify the damaged bearing member.The vibration behavior of applications: In many applications, the bearing stiffness and stiffness of the structure near the same. Because of this feature, as long as the accurate selection of the bearing [...]

  • timken bearing solutions to introduce common injuries

    Typically, if used correctly timken bearing, you can use to reach the fatigue life so far. But there will be accidental injury prematurely, intolerant in usage. This early damage, and fatigue life relative, was called to the quality of failure or accident use limit. Multiple causes for installation, use, pay attention on the lubrication from outside intrusion of foreign matter, the shaft, the thermal effect of the housing is not sufficient and so [...]

  • TIMKEN bearing noise factor of three major life

    Abstract: Due to the rolling element and raceway relative movement of the intrusion of dust and dirt, so that the rolling elements and raceway surface wear. The amount of wear is large, the bearing clearance, noise, vibration increases, reducing the running accuracy of the bearing, and thus directly affect the accuracy of some hosts. Because some of the bearings used in precision machinery, can be used to limit the amount of wear TIMKEN bearing l [...]

  • TIMKEN bearing structure vibrating features and advantages

    Bearings for vibrating screen is one of the important components of the vibration screening equipment, their quality will have a direct impact on screening equipment performance and long life than ordinary bearings, special bearings for vibrating screen also has distinct features and advantages.Vibrating screen special bearing with low noise, good stability, low temperature rise, didn't get up early fatigue characteristics and long life. Vibratin [...]

  • How to prevent the motor bearings rust corrosion

    (1) make use of solvent-free paint.(2) If possible, use non oxidized varnish components, such as epoxy urethane (Epoxy-urethane) group or an epoxy-modified (Epoxy-) based varnish.(3) impregnated with melamine-alkyd paints, it should adjust the curing temperature and curing time, curing temperature is higher than 130 ℃ (eg 135 ℃) and the curing time is greater than 180min appropriate, and the process must be strictly enforced, especially in hot an [...]

  • Fracture failure analysis of retaining part of TIMKEN bearings

    On the fracture site for scanning electron microscopic observation on high, discover its features have the following several points:① magnification observation micro-morphology of many fan-shaped pattern that is visible.② crack front arc is fatigue, and there is a lot of corrosion pits.③ morphology of different angles fan-shaped pattern different, different crack connection fan pattern is formed. Observation of crack propagation in a high area, f [...]

  • Four methods of removing TIMKEN bearings

    A, push methodPress thrust bearing, stable and reliable work, no damage to the machine and TIMKEN bearing shielded room. Press a manual push, mechanical or hydraulic press press.Note: press to be in the center of the shaft, shall not be pressed too.B, knock methodStrike force is usually added to the bearing inner ring, shielded room tapping force should not be added to the bearing rolling body and a holding frame, the method is easy to use, but e [...]

  • Common TIMKEN sliding bearing failures

    Work in sliding friction of sliding bearing TIMKEN bearings. Sliding bearing work steady, reliable, noise-free. Liquid lubrication, sliding surfaces are separated from oil without direct contact, can also significantly reduce friction losses and surface abrasion, oil film also has a certain degree of shock absorption. Application of sliding bearing, use is very extensive, bearing failures we've met our how to solve it? What better ways? Below I'l [...]

  • TIMKEN fan bearing malfunction causes and removal methods

    1, fault analysis: round-leaf with adapter sleeve and bearing housings on either side fixation combined with. Re-test free-end bearing high-temperature and vibration of high value fails, open the bearing cover, manual slow Rotary fan, found in the hinge of a particular position of TIMKEN roller bearings, in the non-scrolling as in loading area. so high can determine bearing clearance operation changes and installation clearance may not be suffici [...]

  • TIMKEN bearing lubrication oil lubrication methods

    Oil lubrication lubrication of TIMKEN bearings are commonly used methods are:(1) manual lubricationFound bearing lubricant is low, a Lubricator oil supply in due time, this is the most original way. Oil content in this way is difficult to maintain a certain, the high risk of inadvertently forget to refuel, usually only used in light, slow or intermittent movement situations. Best setting dust cap or ball valve on the oil hole, felt, cotton, wool [...]

  • Working principle of deep groove ball bearings

    Working principle  Deep groove ball bearings radial load, can withstand the radial load and axial load. When you only take radial loads, contact angle is zero. When a deep groove ball bearing with larger radial internal clearance time, performance with angular contact ball bearings, can accommodate large axial loads. TIMKEN bearings-friction coefficient is small, high limiting speed, especially in axial load under a large fast-moving condition, d [...]

  • TIMKEN bearing Cleanliness important relationship of fever

    In the popular situation, TIMKEN bearings grease fill, always beyond directly involved in lubrication practice demand full holding shelves and rolling mill bearing cover cavity, and form an outline of the periphery of the rolling element. In this process, because the excess grease resistance, the bearing temperature increases rapidly. Although most of the excess grease is squeezed out early in the operation, and squeeze in the raceway attachments [...]

  • Maintenance TIMKEN bearings general steps

    1) track TIMKEN bearings in the mill and recorded. Can provide customers with a spherical bearing block maintenance service record card can be used to record bearing seat number, roll number, chassis number, the location of the bearing on the mill, the outer ring bearing area and tonnage of rolled products and bearing the number of hours worked data. Record card should be updated at any time and facilitate the maintenance personnel check with the [...]

  • Pay attention to the analysis of TIMKEN automobile bearing disassembly method and skill

    Automobile Bearings when removing and installing the same carefully. Careful not to damage the bearings and other parts, especially the interference fit TIMKEN bearing disassembly, difficult operation. Therefore, in the design stage to think ahead to the convenient disassembly, removal tool based on design is also very important.1, the outer ring of the disassemblyDemolition of the interference fit outer ring, the outer ring arranged beforehand s [...]

1 2 3
Go to Page
There is no message.
Online Messagess
Company:
Email:
Message:
ValidateCode: click refresh <--Not see, click refresh